 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Single Chip CMOS Imager with Integrated Image Signal Processor and JPEG Codec Version 1.8 Products and specifications discussed herein are for evaluation and reference purposes only and are subject to change by TransChip without notice. The information in this document is not a warranty, does not form part of any quotation or contract and does not convey a license under intellectual property rights. Copyright (c) TransChip Israel Research Center, Ltd., 2005. 21 November 2005 Table of Contents 1. INTRODUCTION .................................................................................................................................................. 1 1.1 1.2 1.3 2. FEATURES ......................................................................................................................................................... 1 SPECIFICATIONS................................................................................................................................................ 3 COMPACT 24-PIN CAMERA MODULE ................................................................................................................ 4 FUNCTIONAL DESCRIPTION ........................................................................................................................... 5 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 2.12 2.13 2.14 CONT............................................................................................................................................................... 5 RCLK ............................................................................................................................................................... 5 IMGA............................................................................................................................................................... 6 YUVR .............................................................................................................................................................. 6 JPEG ................................................................................................................................................................ 6 PVI AND SVI .................................................................................................................................................... 6 IMAGER AND ADDRESS GENERATOR................................................................................................................. 7 PIXEL ARRAY CONFIGURATION ........................................................................................................................ 7 BAYER GRID CONFIGURATION.......................................................................................................................... 7 RESOLUTIONS AND FRAME RATES .................................................................................................................... 8 ANALOG PROCESSING....................................................................................................................................... 8 ON-CHIP MICRO CONTROLLER.......................................................................................................................... 8 BAYER TO YUV TRANSLATION UNIT (YUVR)................................................................................................. 9 JPEG COMPRESSION UNIT (JCOR)................................................................................................................... 9 3. RESET AND CLOCK .......................................................................................................................................... 11 3.1 LOW POWER MODES....................................................................................................................................... 11 3.1.1 Startup ....................................................................................................................................................... 11 3.1.2 Bypass........................................................................................................................................................ 11 3.1.3 Power Down .............................................................................................................................................. 11 3.2 PLL CONFIGURATIONS ................................................................................................................................... 11 3.3 DEVICE INITIALIZATION SEQUENCE................................................................................................................ 12 4. TC5747MF24L INTERFACES ........................................................................................................................... 13 4.1 I2C SERIAL INTERFACE ................................................................................................................................... 13 4.1.1 Overview .................................................................................................................................................... 13 4.1.2 Mode of Operation..................................................................................................................................... 14 4.2 PARALLEL VIDEO INTERFACE (PVI) ............................................................................................................... 17 4.2.1 Parallel Mode of Operation....................................................................................................................... 17 4.2.2 External Chip-Select .................................................................................................................................. 19 4.2.3 Qualified Clock Mode ................................................................................................................................ 19 4.2.4 VALIDH Configured as WR#..................................................................................................................... 20 4.2.5 Frame-Rate Control................................................................................................................................... 20 4.2.6 Data ........................................................................................................................................................... 21 4.2.7 Data Markers............................................................................................................................................. 23 4.2.8 Ancillary Data Format............................................................................................................................... 25 4.2.9 Serial Output Mode.................................................................................................................................... 26 4.3 SERIAL VIDEO INTERFACE .............................................................................................................................. 28 TransChip (c) ii 5. HIGH LEVEL API PROGRAMMING .............................................................................................................. 29 5.1 FIRMWARE LOADING ...................................................................................................................................... 29 6. AC/DC SPECIFICATIONS ................................................................................................................................. 30 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 6.10 ABSOLUTE MAXIMUM RATINGS ..................................................................................................................... 30 RECOMMENDED OPERATING CONDITIONS ...................................................................................................... 30 DC ELECTRICAL CHARACTERISTICS ............................................................................................................... 30 PARALLEL VIDEO OUTPUT CLOCK QUALIFIED MODE AC CHARACTERISTICS ................................................ 31 PARALLEL VIDEO OUTPUT CAMERA INTERFACE MODE AC CHARACTERISTICS............................................. 31 PARALLEL VIDEO OUTPUT INTERFACE AC CHARACTERISTICS....................................................................... 32 SERIAL VIDEO OUTPUT INTERFACE AC CHARACTERISTICS............................................................................ 32 SERIAL VIDEO OUTPUT CLOCK QUALIFIED MODE AC CHARACTERISTICS...................................................... 33 SERIAL VIDEO OUTPUT SSI MODE AC CHARACTERISTICS.............................................................................. 33 I2C-COMPATIBLE INTERFACE AC CHARACTERISTICS ..................................................................................... 34 7. MECHANICAL AND ELECTRICAL DRAWINGS ........................................................................................ 36 7.1 7.2 TC5747MF24L 24-PIN PACKAGE................................................................................................................... 36 LENS SPECIFICATION ...................................................................................................................................... 38 TransChip (c) iii List of Figures FIGURE 1: TC5747 FUNCTIONAL BLOCK DIAGRAM ......................................................................................................... 5 FIGURE 2: BAYER GRID CONFIGURATION ......................................................................................................................... 7 FIGURE 3: INITIALIZATION SEQUENCE............................................................................................................................. 12 FIGURE 4: I2C INTERFACE START AND STOP CONDITIONS ........................................................................................... 14 FIGURE 5: I2C PROTOCOL................................................................................................................................................ 14 FIGURE 6: I2C HOST-WRITE ACCESS............................................................................................................................... 15 FIGURE 7: I2C HOST-READ ACCESS ................................................................................................................................ 15 FIGURE 8: I2C HOST-READ MULTIPLE (N) ACCESSES ..................................................................................................... 16 FIGURE 9: PVI QUALIFICATION SIGNAL TIMING ............................................................................................................. 17 FIGURE 10: VERTICAL AND HORIZONTAL QUALIFY SIGNALS.......................................................................................... 17 FIGURE 11: PVI BAYER OUTPUT FORMAT ...................................................................................................................... 18 FIGURE 12: PVI YUV OUTPUT FORMAT ......................................................................................................................... 19 FIGURE 13: RGB 565 OUTPUT ON PARALLEL VIDEO OUTPUT INTERFACE ...................................................................... 19 FIGURE 14: VALIDH AS A WRITE SIGNAL, ACTIVE LOW................................................................................................ 20 FIGURE 15: VALIDH AS A WRITE SIGNAL, ACTIVE HIGH .............................................................................................. 20 FIGURE 16: FRAME RATE CONTROL................................................................................................................................ 20 FIGURE 17: RGB666 THREE-TRANSFERS MODE ............................................................................................................. 22 FIGURE 18: SERIAL DATA-OUT INTERFACE - X2_CLK_OUT = 1 ...................................................................................... 26 FIGURE 19: SERIAL DATA-OUT INTERFACE - X2_CLK_OUT = 0 ...................................................................................... 26 FIGURE 20: SINGLE BYTE TRANSFER MODE.................................................................................................................... 27 FIGURE 21: PARALLEL VIDEO OUTPUT CLOCK QUALIFIED MODE .................................................................................. 31 FIGURE 22: PARALLEL VIDEO OUTPUT CAMERA INTERFACE MODE ............................................................................... 31 FIGURE 23: PARALLEL VIDEO OUTPUT INTERFACE SIGNALS .......................................................................................... 32 FIGURE 24: SERIAL VIDEO OUTPUT INTERFACE SIGNALS ............................................................................................... 32 FIGURE 25: SERIAL VIDEO OUTPUT CLOCK QUALIFIED MODE AC.................................................................................. 33 FIGURE 26: SERIAL VIDEO OUTPUT SSI MODE ................................................................................................................ 33 FIGURE 27: I2C-COMPATIBLE INTERFACE ....................................................................................................................... 34 FIGURE 28: TC5747 24-PIN MODULE MECHANICAL DRAWING....................................................................................... 36 FIGURE 29: TC5747 24-PIN MODULE MECHANICAL DRAWING CONTINUED................................................................... 37 TransChip (c) iv List of Tables TABLE 1: TC5747 SPECIFICATIONS ................................................................................................................................... 3 TABLE 2: 24-PIN MODULE PIN LIST ................................................................................................................................... 4 TABLE 3: ANALOG CLOCK RATE MODES .......................................................................................................................... 8 TABLE 4: TRANSCHIP MARKERS ..................................................................................................................................... 23 TABLE 5: ITU 656 MARKERS........................................................................................................................................... 24 TABLE 6: ABSOLUTE MAXIMUM RATINGS....................................................................................................................... 30 TABLE 7: RECOMMENDED OPERATING CONDITIONS ....................................................................................................... 30 TABLE 8: DC ELECTRICAL CHARACTERISTICS ................................................................................................................ 30 TABLE 9: PARALLEL VIDEO OUTPUT CLOCK QUALIFIED MODE AC CHARACTERISTICS ................................................. 31 TABLE 10: PARALLEL VIDEO OUTPUT CAMERA INTERFACE MODE AC CHARACTERISTICS ............................................ 31 TABLE 11: PARALLEL VIDEO OUTPUT INTERFACE AC CHARACTERISTICS ...................................................................... 32 TABLE 12: SERIAL VIDEO OUTPUT CLOCK QUALIFIED MODE AC CHARACTERISTICS ..................................................... 33 TABLE 13: SERIAL VIDEO OUTPUT SSI MODE AC CHARACTERISTICS............................................................................. 33 TABLE 14: I2C-COMPATIBLE INTERFACE AC CHARACTERISTICS .................................................................................... 35 TABLE 15: LENS SPECIFICATIONS .................................................................................................................................... 38 TransChip (c) v TC5747 Data Sheet Single Chip CMOS Imager 1. Introduction The TC5747 is a single chip VGA (640 lines over 480 pixels) color CMOS sensor with an integrated color processing and JPEG codec. It is designed to meet the requirements of cellular devices with low power consumption and miniature size. An embedded programmable core with dedicated hardware performs the extensive color processing. An embedded real-time JPEG encoder and compressed frames SRAM store JPEG images on chip. The TC5747 has flexible interfaces and supports multiple video output formats for easy integration into cellular phones. It supports a 16-bit host interface for fast data access and control. 1.1 Features The TC5747 features a state-of-the-art architecture, allowing extremely low power consumption and miniature size. The following are the product highlights. Sensor Array 1/4" optical format VGA resolution 640x480 5m x 5m square pixels Integrated 10 Bit ADC RGB mosaic with micro-lens for high sensitivity Double sampling for fixed pattern noise reduction Separate gains for R, G and B Programmable frame rate up to 20 fps VGA and 40 fps QVGA Programmable window size and filtered-option sub-sampling Image processing Embedded Image Signal Processor (ISP) Embedded micro controller with program memory Faulty pixel mechanism Loadable gamma correction tables Automatic white balance Automatic exposure control Despeckle function Enhanced dynamic range for backlight illumination Programmable 3x3 color correction matrix Programmable 3x3 sharpening or blurring matrix Anti flicker for 50Hz and 60 Hz Horizontal and vertical inversion Digital zoom of 4X, 2X Color adjustments such as: brightness, contrast, saturation Digital effects, such as monochrome, negative, sepia Frame or stamp overlay on the captured image (up to 320x240) Down sampling by 2x, 3x, 4x, 5x, 6x, 7x, 8x TransChip (c) 1 TC5747 Data Sheet Single Chip CMOS Imager JPEG Codec Real-time JPEG encoder and decoder for still images and M-JPEG for motion video Compression of up to VGA YUV 422 format images Decompression of up to VGA resolution, 4:2:2, 4:1:1, 4:2:0 format images Programmable compression ratio, up to 1.8 bits/pixel for VGA image JPEG compression is done in parallel with preview of the video on the LCD Thumbnail image support Portrait images for phone book Compression and decompression from the internal memory Compression can be done after scaling and overlay of frame and stamp data Decompressed image can be resized and re-compressed On screen display On screen display overlay of up to QVGA (320x240) resolution, 4-bit OSD data color table Support of up to two layers of OSD data. The first layer can be used to add frame of stamp to the captured image. The second layer can be composed of one or two non-overlapping regions of OSD for switching messages and icons. Each OSD window has its own 4-bit color table. Support of 32x32 pixel cursor with 4-bit color table Rotation of JPEG images display by 900 or 2700 Video Interface Flexible output formats including: Bayer, RGB (666, 565, 444), YUV/YCrCb 4:2:2 and JPEG 18 bits direct interface to LCD: supports 8/9/16/18 bit output Chip select for two LCD (main and sub) Camera standby mode for host access to the LCD Optional configuration of 8 bits camera interface Horizontal and vertical sync signals CCIR656 compatible signaling markers Optional high-speed bi-directional serial interface Support of two simultaneous video output streams Host Interface 8/16bit bi-directional I80 and M68 access types host interface Optional I2C or UART interface for programming and control Easy to use software API Input clock frequency: 3.6MHz to 32MHz Power consumption, VGA@ 15 FPS is 85 mW. Power management to support low power modes Operation voltage 2.8 +/- 10% Technology: 0.25 um s Operation temperature: -10 to 60 degrees Celsius Packaging types: module with lens. Module can have either flex cable or board-to-board connector. Several pin-out options will be supported to provide selected interface functionality. TransChip (c) 2 TC5747 Preliminary Data Sheet Single Chip CMOS Imager 1.2 Specifications Feature Array format Capture size Pixel size Color filter Supply Voltage Power consumption Power save modes Description VGA - 656x524 physical pixel, 648x492 active pixels for 1/4" optics Configurable window size 5 x 5 RGB Mosaic with micro lens 2.8V 10%, internal regulators for digital and analog supplies 85mW at 15 fps (including color processing) Sleep mode with maximum of 100A current and wake up of less than 100msec. Power down mode with up to 10A current. Input clock frequency A/D converter Down sampling Video output format Video output interface Video synchronization Control interface Internal PLL supports input clocks of 3.6MHz - 32MHz. 10 bit ADC Down sampling with filter by 2X to 8X in both dimensions. YCrCb422 / YUV422 / RGB444 / RGB565 / RGB666 / Raw / JPEG; 8/9/10-bit parallel camera interface or 8/9/16/18 LCD controller data interface Horizontal and vertical sync signals and/or CCIR656 header 6-bit host bus interface I2C compatible interface UART Used also to read JPEG images Variable up to 20 fps for VGA or 40 fps for QVGA HW JPEG encoder/decoder acceleration On-chip 64Kbyte SRAM to store compressed images On-chip 48Kbyte SRAM to store firmware for the ISP Progressive readout; vertical and horizontal inversion options From one line to one frame duration with 250ns granularity. Separate gain for each of the three color components R,G and B Enhanced dynamic range Black level, faulty pixel correction, color correction, auto white balance, auto exposure, anti-flicker, gamma correction, color suppression. Lens shading correction Digital zoom by 2X, 4X. Contrast, brightness, saturation, sharpening, windowing, lookup table Camera module package with lens, optional flex cable or board-toboard connector 4V/lux-sec (including gain) Table 1: TC5747 Specifications Frame rate JPEG JPEG frames memory Program memory Readout control Exposure control AGC Dynamic range control Image enhancement Anti shading Zoom Image controls Camera module Sensitivity TransChip (c) 3 TC5747 Data Sheet Single Chip CMOS Imager 1.3 Compact 24-pin Camera Module The 24-pin camera module option uses I2C and an 8/9-bit parallel video interface. Pin Name SCLK AGND AVDD28 RESET# CLK_IN DGND DOUT[1]/CSDAT# (*) DYUV[0] DYUV[1] DYUV[2] DYUV[3] DYUV[4] DYUV[5] DYUV[6] DYUV[7] / DSDAT VCLKOUT/ DSCLK VALIDH / WR# / DSFRM VALIDV DVDD28 SDIN PS1 PS2 18 19 20 21 22 O I I/O I I 16 17 O O Parallel video interface clock output/ Serial output clock Horizontal VALID output / Write to LCD - active low Serial Output Frame signal Vertical VALID output signal or interrupt output on Frame start 2.8V for digital circuits I C -compatible bi-directional data signal. Open-drain type. Chip operation modes [PS1, PS2]: 00 - Reset 01 - Full operation 11 - Reserved 10 - Reserved Module noise shield GPO pin, Activates the white LED for low light condition 2 # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 I/O I I I I I I I/O I/O I/O I/O I/O Description I2C-compatible input clock signal generated by the I2C master. Analog circuits ground. 2.8V supply for analog circuits. Asynchronous reset input signal; active low 16-32 MHz clock input or crystal input Digital circuits ground. 9th bit data /External Chip Select for data bus; active low Output video data Output video data Output video data Output video data Output video data Output video data / i2c_toggle - Selects between two I C addresses during RESET# 2 I/O I/O Output video data Output video data / Serial Output Data signal Reserved LED control th 23 24 O (*) 9 bit output or chip select options are selected through wire bonding Table 2: 24-pin Module Pin List TransChip (c) 4 TC5747 Preliminary Data Sheet Single Chip CMOS Imager 2. Functional Description The figure below shows the main functional blocks of the TC5747 and the basic signal flow. Figure 1: TC5747 Functional Block Diagram 2.1 CONT The CONT unit controls the TC5747 units via a central programming bus. Its operation is synchronized with the frame image sequence through several interrupt sources. It is directly accessed by the serial interfaces 2.2 RCLK The RCLK unit generates the RESET and CLOCK signals to the various units. TransChip (c) 5 | | | | TC5747 Data Sheet Single Chip CMOS Imager 2.3 IMGA The IMGA unit controls the image array and the analog processing unit. It produces the various timing controls, performs the "Mirror" transformations and the "Fixed Pattern Noise" corrections. After receiving the array pixels (the ADC output) and performing the required corrections and offsets, the data is sent to the YUVR unit for processing, or to the PVI or SVI unit for Bayer output. 2.4 YUVR The YUVR unit transforms the Bayer data received from the IMGA unit into YUV or RGB data by applying several image reconstruction and correction algorithms. Demosaicing, dynamic range enhancement, digital gain, filter downscaling, sharpening or blurring, color correction, gamma correction, RGB to YUV conversion, YUV-to-RGB conversion and cropping for display are all performed in the YUVR unit. Resizing of the image can be done by 2X - 8X to achieve target LCD screen size with full field of view. 2.5 JPEG The JPEG unit performs encoding or decoding of JPEG images. In encode mode it receives YUV 4:2:2 data, and compresses the image into a JPEG stream. The JPEG compressed image is stored in RAM that is accessible to the CONT unit core and to the I2C interface. The JPEG unit can also be configured to send out the RAM content to one of the output units, with optional ancillary data header and checksum. In decode mode, the compressed code is written to the Code memory, and the JPEG unit decodes it into YUV 4:2:2, 4:2:0 or 4:1:1 data. 4:2:0 and 4:1:1 formats are interpolated into 4:2:2 format. YUV data are then sent to the YUVR unit for resizing and cropping. From the YUVR unit the decoded image is sent to the Parallel Video Interface unit for display. Compression of a display ready image, after scaling and overlay of screen bitmap is also supported. The JPEG unit can also output a thumbnail image. 2.6 PVI and SVI The Parallel Video Interface (PVI) and Serial Video Interface (SVI) units are the output interfaces of the TC5747 device. Each interface can be configured to output one of several streams (Bayer, YUV 4:2:2, RGB, JPEG). The PVI can be configured as a parallel video interface or as a serial output interface. TransChip (c) 6 TC5747 Preliminary Data Sheet Single Chip CMOS Imager 2.7 Imager and Address Generator The imager includes a VGA size pixel array, gain, double sampling, black pixel and readout circuits and ADC. The address generator receives timing signals from the control unit and produces the sequence signals to the pixel array for exposure control, read and reset operations. There are several modes of reading the array content, enabling various image resolutions by windowing and by down sampling. At different modes, various modes of power saving are used. VGA sized images can be read at a rate of up to 20 frames per second. For smaller images at higher frame-rates, several working modes are implemented. 2.8 Pixel Array Configuration The pixel array is 648 by 487 active pixels, surrounded by four black columns on each side and 13 black lines above and 14 black lines below the active image array. This results in a total of 656 by 514 pixels. 2.9 Bayer Grid Configuration Each pixel in the array is covered by a color filter, to create a Bayer grid format: The sensor operates in rolling mode, in which the exposure and readout processes are linked. The sampling of each row data is performed at the end of the integration time. After sampling the selected-row data, the row is reset. The row is sampled again after the reset for the double-sampling procedure. The integration of that row starts again according to the exposure parameters. A set of registers defines the total size of the frame and the size of the array that is read out and sent to the YUVR unit for further processing. Another set of registers defines the exposure time that is required for the array. Figure 2: Bayer Grid Configuration TransChip (c) 7 TC5747 Data Sheet Single Chip CMOS Imager 2.10 Resolutions and Frame Rates The following table summarizes the possible resolutions and frame rates that the TC5747 can produce. The calculation for modes 1, 2 and 3 assume an input and color-processing clock of 32MHz. For mode 4, a 16MHz clock is assumed. The analog clock rate varies according to mode. MODE 1 (Full resolution) 32MHz rclk 8MHz pixel clock 8 rclk cycles/pix Full power VGA QVGA- no down sample QVGA-down sample 20 fps Table 3: Analog Clock Rate Modes 20 fps 40 fps (reduced field of view) 40 fps (full field of view) 40 fps (reduced field of view) MODE 2 (MODE1with window) 32MHz rclk 8MHz pixel clock 8 rclk cycles/pix Full power MODE 3 (down-sample, only 1 ADC is used) 32MHz rclk 8MHz pixel clock 8 rclk cycles/pix Slightly reduced power MODE 4 (down-sample with speed-up) 16MHz rclk 4MHz pixel clock 4 rclk cycles/pix Significantly reduced power 2.11 Analog Processing Analog processing includes a separate gain control for each color filtered pixel, dark pixel correction for each color separately, dark and black-offset correction, faulty pixel replacement and 10-bit ADC. 2.12 On-chip Micro Controller The TC5747 is fully controlled by the embedded microcontroller. Once the firmware, which is supplied by TransChip, is loaded, the embedded microcontroller sets the appropriate registers, and runs the automatic image processing algorithms. An external host does not need to access TC5747 registers and set values, nor does it need to run any algorithm. An easy to use API (Application Programming Interface) is provided to set or adjust various camera controls. The API is performed via a small set of host commands, which are sent over the serial interface (I2C or UART), and are interpreted by the embedded microcontroller, to perform specific camera control, or any other defined internal task. The set of host commands include: Color adjustments (Brightness, contrast, saturation, etc) Image Format (size, mirror x and y, etc) Automatic algorithm enable and parameters (Auto Exposure, AWB, Auto Flicker detection and cancellation) The concept of host commands makes it very useful, as it is going to be forward compatible with any of TransChip sensor, since it is not hardware dependent (namely no need to use specific hardware registers. TransChip (c) 8 TC5747 Preliminary Data Sheet Single Chip CMOS Imager TransChip supplies sample C code, which shows how to upload the firmware and use the host commands (software API). The sample includes all the needed C header files. The supplied firmware comes with preset default values for the various controls. Thus even if no single host commands is performed the firmware ensures that the sensor is running properly according to a preset default set. TransChip also supplies a released version of the firmware. The host commands are fully detailed in a separate document. 2.13 Bayer to YUV Translation Unit (YUVR) The YUVR is the color-processing unit. The unit's parameters and mode registers are loaded through the control bus. The Bayer image is received from the IMGA unit, processed by the YUVR unit, and transferred to the PVI unit for output out of the device. While processing the image, statistics are calculated by the YUVR unit. After completing the processing of an image, the YUVR unit produces an interrupt to the CONT unit. The YUVR thus signifies to the CONT that the statistics for the current image are ready, and the CONT may read the results through the main control bus. The YUVR unit receives the Bayer grid as input. For each pixel, two color values are missing and need to be reconstructed. The input accuracy is 10 bits. The YUVR unit reconstructs the RGB per pixel, performs correction algorithms and generates the YUV representation of the image. Digital color processing includes: demosaicing, dynamic range enhancement, digital gain, filter downscaling, sharpening or blurring, flicker detection and removal, color and white balance correction, gamma correction, color suppression, zoom by 2X or 4X, RGB to YUV conversion, YUV-to-RGB conversion, down sample and cropping of RGB for display, RGB formatting (6:6:6, 5:6:5, 4:4:4) are all performed in the YUVR unit. Zoom is performed by creating a full resolution image from a small region in the center of the image. The small region is blown up by 2X or by 4X to the target image size. The missing pixels are interpolated from the original pixels using a filter to provide a smooth appearance. 2.14 JPEG Compression Unit (JCOR) The JPEG unit receives the YUV 4:2:2 image data from the YUVR unit, and performs real-time JPEG compression. A 25K Byte memory is used for the JPEG compression process. The memory is divided into a Raster-to-Block operation buffer and a JPEG-code memory section. The 64K Bytes of memory can hold a full VGA-sized compressed image at a compression ratio of up to 1.7 bits per pixel. The partition of the memory is fully configurable. When a higher compression ratio is used, several images can be stored in the memory. For example, when capturing a VGA-sized image, three compressed images of 0.5 bits per pixel can be stored in the 64K Byte JPEG-code memory section. When capturing a smaller image, a smaller buffer is required for the Raster-to-Block operation. Therefore a larger JPEG-code memory section can be allocated for support of a lower compression ratio. TransChip (c) 9 TC5747 Data Sheet Single Chip CMOS Imager The JPEG-compressed image can be transmitted either on the parallel video output interface or on the serial video output interface. Alternatively, the host can read the JPEG-compressed image from the on-chip JPEGcode memory via the I2C interface. The JPEG unit can optionally create also a thumbnail image for the full resolution compressed image. The JPEG unit can also be configured to send out RAM contents to one of the output units, with optional ancillary data header and checksum. The JPEG unit can also be activated in decompression mode. The compressed code is written to the Code memory, and the JPEG unit decodes it into YUV 4:2:2 data. The YUV data is then sent to the YUVR unit for resizing and cropping. From the YUVR unit the decoded image is sent to the Parallel Video Interface unit for display. TransChip (c) 10 TC5747 Preliminary Data Sheet Single Chip CMOS Imager 3. Reset and Clock 3.1 Low Power Modes The chip operation is controlled by two bits [PS1, PS2]: Chip operation modes [PS1, PS2]: 00 - Startup 01 - Full operation 11 - Sleep 10 - Power down 3.1.1 Startup The camera powers up at start up mode " 00" . Then it moves to full operation mode " 01" . 3.1.2 Bypass To enter bypass mode, send a host command for power save, then provide standby mode " 11" or switch off the input clock. Bypass mode power consumption is 60A. This minimum power is consumed by a minimal power-supply digital regulator. Contents of memories and registers are maintained. The host can access the LCD during bypass mode. To return to full operation from standby mode, switch on the input clock and wait for clock stability, then send a host command for full operation. 3.1.3 Power Down To enter power down mode, send a host command for power down, and then provide power down mode " 10" . Power down mode consumes less than 10A. To return to full operation from power down mode: provide full operation mode " 01" , wait for clock stability, then send a host command for full operation and load the camera program. 3.2 PLL Configurations An on-chip PLL is configured to supply the internal working clock signal in several modes: Bypass mode - internal clock is identical in frequency to input clock. PLL mode, for support of an internal clock in the range of 24-36MHx 8x - internal clock is 8x the input clock, for support of low frequency input (3-4MHz input) 4x - internal clock is 4x the input clock, for support of low frequency input (8-9MHz input) 2x - internal clock is 2x the input clock, for support of medium frequency input (13-16MHz input) 1.5x - internal clock is 1.5x the input clock, for support of high frequency input (20-24MHz input) TransChip (c) 11 TC5747 Data Sheet Single Chip CMOS Imager Each of the two output units, the PVI and SVI have a serial clock whose frequency is a multiple of the input clock. Each clock, rclkp and rclks is configured separately. 3.3 Device Initialization Sequence PS1/2 RESET_N Bypass (Default) Active PLL PowerDown =01 Startup =00 Full On =10 Set PLL Enter PLL mode mode CLKIN PLL lock time PLL_mode = required working multiply BYPASS PLL_PD RCLK Figure 3: Initialization Sequence The Initialization sequence includes the following steps: 1 2 3 4 5 6 After system power-up, the Power Save pins should be put into Startup mode. Clock input and RESET_N should be activated. After the Regulators' wake up time, the Power Save pins should be put into Full-on mode. RESET_N is PLL deactivated. mode should be set. After PLL lock time, Bypass mode may be deactivated. When working in Bypass mode, steps 5 and 6 may be skipped. TransChip (c) 12 TC5747 Preliminary Data Sheet Single Chip CMOS Imager 4. TC5747MF24L Interfaces I2C or UART control interface Parallel Video Interface (PVI) Serial Video Interface (SVI) The TC5747MF24L chip has the following interfaces: 4.1 I2C Serial Interface 4.1.1 Overview The I2C interface is a two-wire bi-directional serial bus. The TC5747 can operate as a slave device only. Both wires (SCL and SDA) are connected to a positive supply via a pull-up resistor, and when the bus is free both lines are high. The output stage of the device must have an open-drain or open collector type IO cell so that a wired-AND function between all devices that are connected on the bus can be performed. Each device is recognized by a unique 7-bit address. The address allocated to TC5747-B0 is 0x47. When performing write operations, add 0 to the LSB to get 0x8E. For a Read operation add 1 to the LSB to get 0x8F. To summarize: Address 0x47 I C Write 0x8E 2 I C Read 0x8F 2 Note: Some operating systems automatically add the 1 or 0 bit to the 7 bit address. The address for the TC5747-A0 is 0x47. A control of the byte order in I2C transactions is provided through setting a register. TransChip (c) 13 TC5747 Data Sheet Single Chip CMOS Imager 4.1.2 Mode of Operation The bus master, typically the host DSP, initiates an access to the TC5747 device. The bus master activates a START condition, and passes the address of the requested device along with the type of access (read or write bit - the MSB or the start byte). The requested device replies with an acknowledge (ACK). The host can then perform as many transactions as it wishes, until the host activates a STOP condition. The bus is considered free after the STOP condition. The data on the SDA pin must be stable during the high period of the clock (SCL) as shown in the figure below. Only the host may change the data while SCL is high. A high-to-low transition marks a START condition, and a low-to-high a STOP condition. Figure 4: I2C Interface START and STOP Conditions The master device activates a START condition, and sends the first byte of data that contains the 7-bit address, and a direction bit (R/W#, 1 for read, 0 for write). The addressed device answers by pulling down the SDA line as acknowledge procedure. Figure 5: I C Protocol 2 The TC5747 expects the first two bytes after the address byte to be the register address of the first register that is to be read or written by the host. Programming is done in host commands level which is translated into a series of register level commands. When writing registers to the TC5747, the following bytes are data bytes. The data for each READ or WRITE access is two bytes long. The TC5747 performs auto increment until the STOP condition is identified. Auto increment is not performed when the initial address is in the address space that is allocated to the On-Chip-Memories. This address space is reserved for tables, where multiple bytes are written to a single address. When reading registers from the TC5747, the register address (2 bytes) should be followed by a repeated START condition, device address, and R/W# bit equal to 1, to change mode from write (address) to read (data). The sequence of loading or reading registers is described in the figure below. The colored boxes represent host-to-slave data transfer. The clear boxes represent slave-to-host data transfer. TransChip (c) 14 TC5747 Preliminary Data Sheet Single Chip CMOS Imager Figure 6: I C Host-Write Access 2 Figure 7: I2C Host-Read Access TransChip (c) 15 TC5747 Data Sheet Single Chip CMOS Imager Figure 8: I C Host-Read Multiple (N) Accesses 2 The host should activate the STOP condition if a direction change is needed. TransChip (c) 16 TC5747 Preliminary Data Sheet Single Chip CMOS Imager 4.2 Parallel Video Interface (PVI) The PVI generates the video output of the TC5747. The interface consists of a vertical frame-start signal and a 10-bit parallel data bus with clock and qualify signals. It supports parallel and serial modes of operation. 4.2.1 Parallel Mode of Operation The PVI produces a clock signal (the CLK_OUT pin), a 10-bit data bus, DOUT[9:0] and qualifying signals that are synchronous to that clock. On each determining edge of CLK_OUT, a single data byte is transferred on the data bus, if qualified by the VALIDH signal. Figure 9: PVI Qualification Signal Timing Valid data are qualified by the VALIDH signal. The VALIDH signal is activated only when image data is sent out on the parallel interface. It is inactive when dark lines are read, or during the vertical blank period. The VALIDH signal can be configured to qualify only the valid image data, or to qualify optional Start-of-line and End-of-line markers. Figure 10: Vertical and Horizontal Qualify Signals TransChip (c) 17 TC5747 Data Sheet Single Chip CMOS Imager The DOUT[9:0] bus carries either the Bayer grid data, the YUV 4:2:2 output data, the RGB data (RGB565, RGB666 or RGB444) or JPEG code according to the TCIF_OUTPUT_FORMAT host command. Bayer Grid data is left-justified. 10-bit Bayer resides on DOUT[9:0] 9-bit Bayer resides on DOUT[9:1] 8-bit Bayer resides on DOUT[9:2] The 8-bit YUV data resides on the DOUT[9:2] output pads, annotated DYUV[7:0]. The 8-bit RGB565 or RGB444 data resides on the DOUT[9:2] output pads. The 9-bit RGB666 data resides on the DOUT[9:1] output pads. RGB666 can also be transmitted using 3 clock cycles on the DOUT bus The 6-bit RGB666 (3-word mode) data resides on the DOUT[9:4] output pads. The 8-bit JPEG data resides on the DOUT[9:2] output pads. For 2-word output formats, RGB444, 565 and 666, the data is packed into 2 words: RGB444: {Blue[3:0], 0x0} RGB565: RGB666: {Red[3:0],Green[3:0]} {Red[4:0], {Red[5:0], Green[5:3]} Green[5:3]} {Green[2:0], Blue[4:0]} {Green[2:0], Blue[5:0]} For 3-word RGB 666 output formats, the data is sent out as 3 words: RGB666: Green[5:0] Blue[5:0] Red[5:0], The active line timing is depicted in the diagrams below. The diagram below shows the active data line where the optional Start-of-line and End-of-line markers are omitted: Figure 11: PVI Bayer Output Format TransChip (c) 18 TC5747 Preliminary Data Sheet Single Chip CMOS Imager Figure 12: PVI YUV Output Format Figure 13: RGB 565 Output on Parallel Video Output Interface The output clock rate for YUV or 2-word RGB output is double the output clock rate for Bayer output. The output clock rate for 3-word RGB666 is double the output clock rate for YUV output. When sending out the data in Bayer-grid format, a " RED" line will always be the first line in the frame. 4.2.2 External Chip-Select A mode may be selected where the data bus may be floated or driven according to an external chip-select input controlled by the CSDAT# pin. The CSDAT# pin is active-low, i.e. when low the DOUT[9:1] or DYUV[7:0] bus pins are driven, and when CSDAT# is high these outputs are put in a tri-state position. The VALIDH, VALIDV and VCLKOUT pins are not affected by the CSDAT# pin. 4.2.3 Qualified Clock Mode The TC5747 supports a mode where the VCLKOUT pin is not active when there is no active data on the parallel interface. TransChip (c) 19 TC5747 Data Sheet Single Chip CMOS Imager 4.2.4 VALIDH Configured as WR# The VALIDH pin may be configured to work as a WRITE signal for applications requiring that the video data is being written into a device. The polarity is programmable. The data is marked as valid only when the VALIDV pin is active. The data should be sampled on the trailing edge of the VALIDH pin. Figure 14: VALIDH as a Write signal, Active Low Figure 15: VALIDH as a Write Signal, Active High 4.2.5 Frame-Rate Control The CONT unit uses the c_outframe signal to control the frame rate. It enables or disables the output of a full frame. When output is disabled, the VALIDH and VALIDV output signals are stuck at an inactive state. The data output bus holds the background value throughout the disabled frame time. Figure 16: Frame Rate Control The c_outframe signal changes on im_frame. The decision if to send or skip the new frame is made on the clock cycle that follows the im_frame signal. TransChip (c) 20 TC5747 Preliminary Data Sheet Single Chip CMOS Imager 4.2.6 4.2.6.1 Data General The type of data (Bayer, RGB, YCrCb 4:2:2 or JPEG) output from the TC5747 is programmable through the TC5747 programming registers, using host commands. The type of data also defines the frequency of the TC5747's output clock signal. 4.2.6.2 Bayer Output When Bayer output is selected, the data volume is one byte per pixel. If Data-Markers are added, 8 more bytes per line must be taken into consideration in the image buffer that is allocated for the application. There are two types of Bayer data lines: " RED" lines - lines that carry Green and Red Bayer components. The Green and Red data bytes are interleaved. The even numbered bytes (0, 2 to 2n) are Green, the odd numbered bytes (1,3 to 2n+1) are Red. " BLUE" lines - lines that carry Blue and Green Bayer components. The Green and Blue data bytes are interleaved. The even numbered bytes (0, 2 to 2n) are Blue, the odd numbered bytes (1,3 to 2n+1) are Green. When sending out the data in Bayer-grid format, a " RED" line will always be the first line in the frame. 4.2.6.3 YCrCb 4:2:2 Output When YCrCb 4:2:2 output is selected, the data volume is two bytes per pixel. If Data-Markers are added, 8 more bytes per line must be taken into consideration in the image buffer that is allocated for the application. The data in the YCrCb 4:2:2 output format is ordered in several configurations, according to the setting in the Color_order bits in the video output control registers: 00 - SOL, Y0, U0, Y1, V0, Y2, U2, Y3, V3, to Yn-2, Un-2, Yn-1, Vn-2, EOL 01 - SOL, Y0, V0, Y1, U0, Y2, V2, Y3, U3, to Yn-2, Vn-2, Yn-1, Un-2, EOL 10 - SOL, U0, Y0, V0, Y1, U2, Y2, V3, Y3, to Un-2, Yn-2, Vn-2, Yn-1, EOL 11 - SOL, V0, Y0, U0, Y1, V2, Y2, U3, Y3, to Vn-2, Yn-2, Un-2, Yn-1, EOL 4.2.6.4 RGB565 Output When RGB565 output is selected, the data volume is two bytes per pixel. Output data are transmitted in the same manner and frequency as the YCrCb 4:2:2 output format, on DOUT[9:2]. The first byte of each pixel carries 5 bits of the Red color component, and the 3 MSB of the Green. The second byte carries the 3 LSB of the Green color component, and the 5 bits of the Blue color component. TransChip (c) 21 TC5747 Data Sheet Single Chip CMOS Imager 4.2.6.5 RGB666 Output When RGB666 output is selected, the data volume is two 9-bit " words" per pixel. Two modes can be selected for RGB666 data. Two-transfers Mode When RGB666 output is selected, the data volume is two 9-bit " words" per pixel. No extra pixels are required beyond the VGA/QVGA size. The output data is transmitted in the same manner and frequency as the YCrCb 4:2:2 output format, on DOUT[9:1]. The first byte of each pixel carries 6 bits of the Red color component, and the 3 MSB of the Green. The second byte carries the 3 LSB of the Green color component, and the 6 bits of the Blue color component. Three-transfers Mode When three-transfer RGB666 output is selected, the data volume is three 6-bit " words" per pixel. No extra pixels are required beyond the VGA/QVGA size. The output data is transmitted on DOUT[9:4]. The order of transmission is Red, Green and Blue. Figure 17: RGB666 Three-transfers Mode The output data is transmitted in the double the frequency as the YCrCb 4:2:2 output format, 3 consecutive clock cycles carry valid data, and the fourth clock cycle is skipped. No valid data is active on this clock cycle, and VALIDH is inactive. 4.2.6.6 RGB444 Output When RGB444 output is selected, the data volume is two bytes per pixel. The output data is transmitted in the same manner and frequency as the YCrCb 4:2:2 output format, on DOUT[9:2]. The first byte of each pixel carries 4 bits of the Red color component, and the 4 bits of the Green. The second byte carries the 4 bits of the Blue color component on DOUT[9:6], and is padded by 6 zeros on DOUT[5:0]. 4.2.6.7 JPEG Output When JPEG output is selected, the compressed code is sent out on the parallel data bus, qualified by VALIDH. To support ancillary data format as defined in the ITU 656 and ITU 1364 standards, an optional ancillary data packet header may be added before each consecutive packet of bytes of JPEG code. A Checksum byte may be added following the data bytes. The last " packet" of JPEG code may contain less than packet number of bytes, and the " payload byte" in the packet header reflects the actual size. TransChip (c) 22 TC5747 Preliminary Data Sheet Single Chip CMOS Imager 4.2.7 Data Markers Extra optional data markers are inserted at the beginning and end of each image line. The user may select between TransChip-specific markers, and markers that conform to the ITU 656 standard. 4.2.7.1 TransChip Markers A " Timing signal" or Marker is defined in the ITU 656 standard as a sequence of four bytes, the first three bytes holding reserved values of FF 00 00, and the fourth byte composed of a collection of bits whose function is defined in the standard. The TransChip markers utilize the format of the markers as defined in the standard, but redefines two bits in the last marker byte. There are four types of markers: Start of First Line marker - This marker precedes the data of the first line in a frame. Start of Line Marker - This marker precedes the data of each line in a frame, except for the first line. When Bayer output mode is selected, bit #5 of the marker content differentiates between a " red" line and a " blue" line (0 and 1 respectively). End of Last Line Marker - This marker immediately follows the data of the last line in a frame. End of Line Marker - This marker immediately follows the data of each line in a frame, except for the last line. All markers are 4 bytes long. The first 3 bytes of all markers are identical, and annotate the marker header. The marker content is " FF 00 00 xy" , where xy is different for each marker type. Marker SOFL SOLR (YCrCb or "red" line) SOLB ("blue" line) EOLL EOL Marker Header 0xFF 0xFF 0xFF 0xFF 0xFF 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 Marker content DOUT[9:2] / DYUV[7:0] 0xC7 0x80 0xAB 0xDA 0x9D Table 4: TransChip Markers Bits [7:4] of the Marker-content byte carry the marker information: Bit [7] - Always 1 to avoid 0x00 code Bit [6] - Special frame markers (start-first-line/end-last-line) Bit [5] - For Bayer - line " color" (0 for Red, 1 for Blue) Bit [4] - End/Start bit, 0 for Start-of-line marker, 1 for End-of-line Bits [3:0] of the Marker-content byte provide parity check capability, allowing for one-bit errors to be corrected, and two-bit errors to be detected, according to ITU-656-4 Standard. TransChip (c) 23 TC5747 Data Sheet Single Chip CMOS Imager 4.2.7.2 ITU 656 Markers A " Timing signal" or Marker is defined in the ITU 656 standard as a sequence of four bytes, the first three bytes holding reserved values of FF 00 00, and the fourth byte composed of a collection of bits whose function is defined in the standard. Bits [7:4] of the Marker-content byte carry the marker information: Bit [7] - Always 1 to avoid 0x00 code Bit [6] - F - field 0 or field 1 Bit [5] - V - blank or active video line indication (0 for active, 1 for blank) Bit [4] - H - End/Start bit, 0 for Start-of-line marker, 1 for End-of-line Bits [3:0] of the Marker-content byte provide parity check capability, allowing for one-bit errors to be corrected, and two-bit errors to be detected, according to ITU-656-4 Standard. When adhering to the bit-definition of the ITU-656 standard, there is a need to distinguish between consecutive frames, either by inserting markers on at least one blank line between frames, or by toggling the field bit on every frame start. The PVI supports the following options. Marker SAV - active SAV - blank EAV - active EAV - blank SAV - active SAV - blank EAV - active EAV - blank Field 0 0 0 0 1 1 1 1 Marker Header 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 Marker content DOUT[9:2] / DYUV[7:0] Table 5: ITU 656 Markers TransChip (c) 24 TC5747 Preliminary Data Sheet Single Chip CMOS Imager 4.2.7.3 Avoiding Marker Emulation When the Send-Markers mode is enabled, care has to be taken to avoid marker-emulation inside the data itself. When YCrCb 4:2:2 output mode is selected, there is no contention between marker header contents and the transmitted data, because the Y data values are limited to the range of 16-235, and the Cr and Cb data values are limited to the 16-240 range. 0x00 and 0xFF values never occur inside the image data values. When Bayer output is selected, the data has to be modified, so that 0xFF and 0x00 values are removed from the data content, and replaced by their nearest allowed values (0xFE and 0x01 respectively). When RGB565 output is selected, the data has to be modified, as in the case of the Bayer output. 0xFF and 0x00 values are removed from the data content, and replaced by their nearest allowed values. The first byte of RGB565 is replaced by 0xF7 or 0x08. The second byte of RGB565 is replaced by 0xFE or 0x01. When RGB666 output is selected, the data has to be modified, as in the case of the Bayer output. 0xFF and 0x00 values are removed from the data content, and replaced by their nearest allowed values. TBD When RGB444 output is selected, the data has to be modified, as in the case of the Bayer output. 0xFF and 0x00 values are removed from the data content, and replaced by their nearest allowed values. The first byte of RGB444 is replaced by 0xEF or 0x10. The second byte of RGB444 is replaced by 0xF0 or 0x01. JPEG code cannot be modified. However, there is no need for any modification if Ancillary format is used for JPEG transmission. 4.2.8 Ancillary Data Format The ITU-1364 defines the ancillary data format that may be transmitted during blank lines of video, as defined in the ITU 656 standard. Immediately following a blank line " Timing signal" , an ancillary data packet may be added. If an ancillary data header is detected instead of the blank video data, as defined by the standard (a sequence of 0x80 0x10), ancillary data can be extracted. An ancillary data header is defined as a sequence of 6 bytes: 0x00 0xFF 0xFF ID1 ID2 Data-SIZE/4 The header is followed by data (4 to 252 bytes). A Check-sum byte follows the data as the last byte of the packet. The ancillary header and checksum are optionally produced by the JPEG unit. The PVI does not differentiate between header and JPEG code. TransChip (c) 25 TC5747 Data Sheet Single Chip CMOS Imager 4.2.9 Serial Output Mode The Transmitted data size for Serial output mode is 8 bits per transmitted " word" . Bayer output provides 8 bits per pixel, and YUV and RGB output provides 16 bits per pixel. The bytes are sent with the MSB first, LSB last. During continuous transfer, the MSB of byte N immediately follows the LSB of byte (N-1). The TC5747 serial output interface can be configured to work in two different modes: Clock-qualify mode - A two wire interface with clock and output data signals. The TC5747 acts as a master of the interface. It activates the serial clock signal when there is valid data to be sent out. SSI mode - A three wire interface, with clock, output data and frame signals. The TC5747 acts as a master of the interface, producing all three signals. Clock-Qualify Mode 4.2.9.1 The serial interface consists of two pins: DSCLK - Data Serial Clock output pin -1X or 2X the rate of the data output TC5747 generates DSCLK signal from its general clock input signal. DSDAT - Serial Data output pin. The TC5747 acts as a master of the interface. It activates the serial clock signal when there are valid data to be sent out. Serial Clock Polarity - Clock is inactive at zero Serial Clock Phase - Drive data on positive edge of Serial clock signal (DSCLK/2), latch on negative edge Figure 18: Serial Data-Out Interface - x2_clk_out = 1 Figure 19: Serial Data-Out Interface - x2_clk_out = 0 TransChip (c) 26 TC5747 Preliminary Data Sheet Single Chip CMOS Imager 4.2.9.2 SSI Mode The serial interface consists of three pins: DSCLK - Data DSDAT DSFRM Serial Clock output pin - Serial Data output pin. - Frame signal in early-frame mode The TC5747 acts as a master of the interface. It activates the Frame signal one clock period before there is valid data to be sent out. Transfer datum size configurable. There are three options: Transfer datum size is a single byte. Transfer datum size is a single line (size is according to output image size and output mode). Transfer datum size is a single image. This configuration can be used only in a mode that combines the SSI-mode with the clock-qualify mode. DSFRM Signal The DSFRM signal notifies of a transfer of a complete data unit. There are three configurations, as described below. Single Byte Transfer Mode The 8 bits of the transfer byte are sent out on the eight following effective edges of the DSCLK signal. When the last bit of the byte is sent out, the DSFRM signal may be active again. If it is active, the following byte transfer begins on the next effective edge of DSCLK. Figure 20: Single Byte Transfer Mode Image-line Transfer Mode In this mode, DSFRM is activated one clock before the continuous transfer of a complete image line. Transfer size should be configured on the receiving side according to the image line size, taking into consideration the SAV and EAV markers, if used. Frame Transfer Mode In this mode, the DSFRM signal is activated once in a frame, one clock cycle before the first byte of the image is transferred out. The DSFRM signal duration is also configurable, to be of one clock cycle duration, or to be active until the last byte of data in the transfer is transmitted. The second mode can be used to generate an interrupt inside the receiving device, once the complete data has been transferred. TransChip (c) 27 TC5747 Data Sheet Single Chip CMOS Imager DSCLK Output The DSCLK output can be configured to be continuous or gated. The gated option should be used when DSFRM is in the Frame-transfer mode. 4.3 Serial Video Interface The TC5747 Serial Video interface unit is identical to the PVI unit described above, with two exceptions: Supports only serial interface Support also SSI input of data. The data input is controlled through the I2C. The addition of input direction provides a high speed input serial interface for decompression of JPEG images. TransChip (c) 28 TC5747 Preliminary Data Sheet Single Chip CMOS Imager 5. High Level API Programming All TC5747 series products come with a flexible software API (Applications Program Interface) for integration of the product and interfacing it to a wide range of hosts. The API is based on a set of defined host commands. The TC5747 is controlled by an embedded microcontroller. The microcontroller runs the firmware that is supplied by TransChip. The microcontroller receives the host commands, and executes them to perform various camera control functions. 5.1 Firmware Loading The microcontroller firmware (program) may be loaded through the host interface. (When using I2C or UART for control, firmware is loaded either using the I2C interface or the UART interface). Once the program is loaded, the microcontroller sets the registers and controls the entire chip according to the firmware preset defaults and according to host commands which the microcontroller receives through the control interfaces. TransChip (c) 29 TC5747 Data Sheet Single Chip CMOS Imager 6. AC/DC Specifications The TC5747 chip excels in low power consumption 6.1 Absolute Maximum Ratings Symbol VDD TA Parameter DC supply Voltage Storage Temperature Table 6: Absolute Maximum Ratings Min -30 Max 4.0V 70oC 6.2 Recommended Operating Conditions Symbol VDD TA Parameter DC supply Voltage - 2.8V nominal Operating Temperature Table 7: Recommended Operating Conditions Min 2.52 -10 Max 3.08V 60oC 6.3 DC Electrical Characteristics Symbol VIH VIH VIL 1 2 Characteristic Input Hi-Volt Input Hi-Volt Input Low-Volt Input Low-Volt Input Hi-Volt Input Low-Volt Condition VDD=2.8V;Temp=25 C VDD=2.8V;Temp=25 C VDD=2.8V;Temp=25 C VDD=2.8V;Temp=25 C VDD=2.8V;Temp=25 C VDD=2.8V;Temp=25 C VOL=0.5*VDD;Temp=25 C VOH=0.5*VDD;Temp=25 C Specifications Min 2.0V Typ Max 1 0.8V VIL2 VOH VOL IOL IOH IDDmax II/Ioz 2.4V 0.4V 13.3mA 19.4mA 15mA TBD +/- 1uA +/- 10uA Supply current in working conditions Input leakage/ Output tristate leakage VDD=2.8V;Temp=25 C VGA mode, 15 fps Table 8: DC Electrical Characteristics 1 - All pins except clk_in 2 - clk_in TransChip (c) 30 TC5747 Preliminary Data Sheet Single Chip CMOS Imager 6.4 Parallel Video Output Clock Qualified Mode AC Characteristics Figure 21: Parallel Video Output Clock Qualified Mode Parameter Tsu Th Description Data setup before effective edge of VALIDH Specifications Min 150 25 Max - Units ns ns Table 9: Parallel Video Output Clock Qualified Mode AC Characteristics * Results depend on device frequency and mode. The results in this table are for 32MHz, PVI CLK = clk_in. 6.5 Parallel Video Output Camera Interface Mode AC Characteristics Figure 22: Parallel Video Output Camera Interface Mode Parameter Tsu Th Description Data setup before effective edge of VCLKOUT Specifications Min 150 25 Max - Units ns ns Table 10: Parallel Video Output Camera Interface Mode AC Characteristics * Results depend on device frequency and mode. The results in this table are for 32MHz, PVI CLK = clk_in. TransChip (c) 31 TC5747 Data Sheet Single Chip CMOS Imager 6.6 Parallel Video Output Interface AC Characteristics Tsu VCLKOUT VALIDH/ VALIDV DOUT[9:0] Th Th Figure 23: Parallel Video Output Interface Signals Parameter Tsu Th Description Data setup before effective edge of VCLKOUT Min 150 25 Max - Units nsec nsec Table 11: Parallel Video Output Interface AC Characteristics 6.7 Serial Video Output Interface AC Characteristics Figure 24: Serial Video Output Interface Signals Parameter Tsersu Tserh Description Data setup (DSDAT and DSFRM) before negative edge of DSCLK. Data hold (DSDAT and DSFRM) before negative edge of DSCLK. Min 5 5 Max - Units nsec nsec TransChip (c) 32 TC5747 Preliminary Data Sheet Single Chip CMOS Imager 6.8 Serial Video Output Clock Qualified mode AC Characteristics Figure 25: Serial Video Output Clock Qualified mode AC Parameter Tsersu Tserh Description Data setup (DSDAT and DSFRM) before negative edge of DSCLK Data hold (DSDAT and DSFRM) before negative edge of DSCLK. Specifications Min 5 5 Max - Units ns ns Table 12: Serial Video Output Clock Qualified mode AC Characteristics * Results depend on device frequency and mode. The results in this table are for 32MHz, SVI CLK = clk_in. 6.9 Serial Video Output SSI mode AC Characteristics Figure 26: Serial Video Output SSI mode Param Tsersu Tserh Description Data setup (DSDAT and DSFRM) before negative edge of DSCLK Data hold (DSDAT and DSFRM) before negative edge of DSCLK Specifications Min 5 5 Max - Units ns ns Table 13: Serial Video Output SSI mode AC Characteristics * Results depend on device frequency and mode. The results in this table are for 32MHz, SVI CLK = clk_in. TransChip (c) 33 TC5747 Data Sheet Single Chip CMOS Imager 6.10 I2C-Compatible Interface AC Characteristics Figure 27: I C-Compatible Interface 2 TransChip (c) 34 TC5747 Preliminary Data Sheet Single Chip CMOS Imager Parameter Fmax Tcyc Tstsu Tsth Tih Tisu Tpsu Toh Tosu Description Maximum SCLK frequency SCLK cycle duration Specifications Min 2500 125 250 125 250 125 125 250 Max 400 Units KHz ns ns ns ns ns ns ns ns Start condition SCLK setup time Start condition SCLK hold time SDIN input hold time SDIN input setup time Stop condition SCLK setup time SDIN output hold time SDIN output setup time Table 14: I2C-Compatible Interface AC Characteristics Note: Data entered is calculated for 400KHz SCLK frequency. TransChip (c) 35 TC5747 Data Sheet Single Chip CMOS Imager 7. Mechanical and Electrical Drawings 7.1 TC5747MF24L 24-pin Package Following is a mechanical drawing of the TC5747MF24L 24-pin module. Figure 28: TC5747 24-pin Module Mechanical Drawing TransChip (c) 36 TC5747 Preliminary Data Sheet Single Chip CMOS Imager Figure 29: TC5747 24-pin Module Mechanical Drawing Continued TransChip (c) 37 TC5747 Data Sheet Single Chip CMOS Imager 7.2 Lens Specification Characteristic Material Structure Effective Focal Length Focal Range F Number Angle of View (FOV) 1/4 " Lens module Heat resistant plastic Three element (one glass and two plastic) 3.72 mm 40cm - infinity 2.4 55 Diagonal 45 Horizontal 35 Vertical Focus IR Filter Resolution (MTF) for RGB Factory fixed focused Included 0.47 @ 45 cy/mm on-axis 0.40 @ 45 cy/mm Vertical 0.30 @ 45 cy/mm Horizontal 0.27 @ 45 cy/mm Diagonal Relative Illumination 100% On-Axis 75% Vertical 65% Horizontal 55% Diagonal TV Distortion Module Height <1% 5.5 mm +0.1 mm/ -0.2mm Table 15: Lens Specifications TransChip (c) 38 |
Price & Availability of TC5747
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |